Kepco KLR Series Developers Guide Bedienungsanleitung PDF herunterladen (Seite 5)

KLR DEVGD 020498 iii

TABLE OF CONTENTS

SECTION PAGE

SECTION 7 - IEEE 488.2 (GPIB) INTERFACE

7.2 IEEE 488 (GPIB) Bus Protocol ................................................................................................................... 7-1

7.2.1 Changing the GPIB Address ................................................................................................................... 7-3

SECTION 8 - RS 232C INTERFACE [STANDARD MODELS ONLY]

8.2 RS232-C Operation [Standard Models Only].............................................................................................. 8-1

8.2.1 RS 232 Implementation [Standard Models Only] .................................................................................... 8-1

8.2.2 Data Transfer Protocols [Standard Models Only].................................................................................... 8-2

8.2.2.1 Echo Mode [Standard Models Only] .................................................................................................. 8-3

8.2.2.2 Prompt Method [Standard Models Only] ............................................................................................ 8-3

8.2.2.3 XON XOFF Method [Standard Models Only] ..................................................................................... 8-3

8.2.2.4 Isolating RS 232 Communications Problems [Standard Models Only] .............................................. 8-4

SECTION 9 - LAN INTERFACE [E-Series MODELS ONLY]

9.2 Using Port 80 (Web Interface) .................................................................................................................... 9-1

9.3 Using Port 5024 (Telnet)............................................................................................................................. 9-1

9.4 Using Port 5025 (SCPI-RAW)..................................................................................................................... 9-2

9.5 Using Port 1024 (VXI-11)............................................................................................................................ 9-2

9.6 Using Port 5044 ( *TRG command)............................................................................................................ 9-2

9.7 SUNRPC Port 111 ...................................................................................................................................... 9-2

APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS

A.2 *CLS — Clear Status Command ............................................................................................................... A-1

A.3 *ESE — Standard Event Status Enable Command................................................................................... A-1

A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2

A.5 *ESR? — Event Status Register Query..................................................................................................... A-2

A.6 *IDN? — Identification Query..................................................................................................................... A-2

A.7 *OPC — Operation Complete Command .................................................................................................. A-3

A.8 *OPC? — Operation Complete Query....................................................................................................... A-3

A.9 *OPT? — Operation Complete Query ....................................................................................................... A-4

A.10 *RCL — Recall Command ......................................................................................................................... A-4

A.11 *RST — Reset Command.......................................................................................................................... A-4

A.12 *SAV — Save Command........................................................................................................................... A-4

A.13 *SRE — Service Request Enable Command ............................................................................................ A-5

A.14 *SRE? — Service Request Enable Query ................................................................................................. A-6

A.15 *STB? — Status Byte Register Query ....................................................................................................... A-6

A.16 *TRG — Trigger Command ....................................................................................................................... A-6

A.17 *TST? — Self Test Query .......................................................................................................................... A-6

A.18 *WAI — Wait Command ............................................................................................................................ A-6

APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS

B.1 Introduction................................................................................................................................................ B-1

B.2 Numerical Values....................................................................................................................................... B-2

B.3 ABOR

t Command...................................................................................................................................... B-2

B.4 CAL

ibrate Commands and Queries .......................................................................................................... B-2

B.5 DISP

lay[:Window]:TEXT[:DATA]? Query.................................................................................................. B-2

B.6 INITiate[:IMMediate] Command................................................................................................................ B-2

B.7 INIT

iate:CONTinuous Command .............................................................................................................. B-3

B.8 INITiate:CONTinuous Query..................................................................................................................... B-4

B.9 [SOUR

ce:]LIST:CLEar Command............................................................................................................. B-4

B.10 [SOUR

ce:]LIST:CONTrol Command ......................................................................................................... B-4

B.11 [SOURce:]LIST:CONTrol? QUERY........................................................................................................... B-4

B.12 [SOUR

ce:]LIST:CONtrol:POINts? Query.................................................................................................. B-4

1 2 3 4 5 6 7 8 9 10 ... 127 128

Kommentare zu diesen Handbüchern

Keine Kommentare

Kepco KLR Series Developers Guide Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Stromversorger Kepco KLR Series Developers Guide